The Tron Box Written by The GREAT Captain Crunch!!

The Tron Box                 Written by The GREAT Captain Crunch!!
                             Courtesy of  Exodus

   ------------------R-----F----
   I   I   I                   I
   I   I   I                   I-
  (C) (C) (C)
   I   I   I                   I-
   I   I   I                   I
   -----------------------------

 (C)=CAPACITOR
  F =FUSE
  R =RESISTOR
 I,- ARE WIRE
  PARTS LIST:
 (3) ELECTROLYTIC CAPACITORS RATED AT 50V(LOWEST) .47UF
 (1) 20-30OHM 1/2 WATT RESISTOR
 (1) 120VOLT FUSE (AMP RATING BEST TO USE AT LEAST HALF OF TOTAL
     HOUSE CURRENT OR EVEN LESS IT KEEPS YOU FROM BLOWING YOUR
     BREAKER JUST IN CASE...)
 (1) POWER CORD (CUT UP AN EXTENSTION CORD. NEED PLUG PART AND WIRE)
 (1) ELECTRICALLY INSULATED BOX


REST OF SIF YOUR DONT FILL COMFORTABLE ABOUT ELECTRICITY THEN DONT
PLAY WITH THIS THERE IS VOLTAGE PRESENT THAT WILL
***KILL*** YOU......................

THE THING WORKS WHEN THE LOAD IN YOUR HOUSE IS LOW LIKE AT NIGHT TIME. IT
WILL PUT A REVERSE PHASE SIGNAL ON THE LINE AND CANCEL OUT THE OTHER PHASE
AND PUT A REVERSE PHASE RUNNING EVERYTHING IN THE HOUSE. WELL IF YOU HAVE
EVER SWITCHED THE POWER LEADS ON A D.C. (BATTERY POWERED) MOTOR YOU
WILL SEE THAT IT RUNS BACKWARDS WELL YOUR ELECTRIC METER SORT OF WORKS
THIS WAY...SO REVERSE PHASE MAKES THE METER SLOW DOWN AND IF YOUR
LUCKY IT WILL GO BACKWARDS. ANYWAY IT MEANS A CHEAPER ELECTRIC BILL.

Read More

Olive Box Plans Courtesy of Exodus

Olive Box Plans                        Courtesy of Exodus

    This is a relatively new box, and all it basically does is serve as a phone
ringer. You have two choices for ringers, a piezoelectric transducer (ringer),
or a standard 8 ohm speaker. The speaker has a more pleasant tone to it, but
either will do fine. This circuit can also be used in conjunction with a rust
box to control an external something or other when the phone rings. Just connect
the 8 ohm speaker output to the inputs on the rust box, and control the pot to
tune it to light the light (which can be replaced by a relay for external
controlling) when the phone rings.

             ______________
            |              |        ^
       NC --|-- 5      4 --|-----/\/\/------->G
            |              |      / R2
G<----)|----|-- 6      3 --|-- NC
    | C3    |      U1      |
     -------|-- 7      2 --|---------- --- -- - > TO RINGER
            |              |
        ----|-- 8      1 --|--
       |    |______________|  |
       |                       ---/\/\/----|(----- L1
       |                           R1      C1
        ------------------------------------------ L2

                  a. Main ringer TTL circuit

(>::::::::::::::::::::::::::::::::::::::::::::::::::::::::<)

                                   _
FROM PIN 2 < - -- --- ----------| |_| |------------->G
                                    P1

                  b. Peizoelectric transducer

(>::::::::::::::::::::::::::::::::::::::::::::::::::::::::<)

                                                      __  /|
FROM PIN 2 < - -- --- ---------|(---------.  .-------|  |/ |
                                          >||<       |S1|  |
                                          >||<     --|  |  |
                                          >||<    |  |__|\ |
                              G<---------.>||<.---        \|
                                           T1
                c. Elctro magnetic transducer
Parts List
----------

U1 - Texas Instruments TCM1506
T1 - 4000:8 ohm audio transfomer
S1 - 8 ohm speaker
R1 - 2.2k resistor
R2 - External variable resistor; adjusts timing frequency
C1 - .47uF capacitor
C2 - .1uF capacitor
C3 - 10uF capacitor
L1 - Tip
L2 - Ring
     L1 and L2 are the phone line.


Shift Rate:
-----------

  This is the formula for determining the shift rate:

                   1                   1
    SR = --------------------- = ------------ = 6.25 Hz
         (DSR(1/f1)+DSR(1/f2))    128     128
                                 ----  + ----
                                 1714    1500


              DSR = Shift Devider Rate ratio = 128
                f1 = High Output Frequency = 1714
               f2 = Low Output Frequency = 1500

Read More

The Lunch BoxCourtesy of Exodus

The Lunch Box                          Courtesy of Exodus

Introduction
===========

The Lunch Box is a VERY simple transmitter which can be handy for all sorts of
things. It is quite small and can easily be put in a number of places. I have
successfully used it for tapping fones, getting inside info, blackmail and
other such things. The possibilities are endless. I will also include the plans
or an equally small receiver for your newly made toy. Use it for just about
anything. You can also make the transmitter and receiver together in one box
and use it as a walkie talkie.

Materials you will need
======================

(1) 9 volt battery with battery clip
(1) 25-mfd, 15 volt electrolytic capacitor
(2) .0047 mfd capacitors
(1) .022 mfd capacitor
(1) 51 pf capacitor
(1) 365 pf variable capacitor
(1) Transistor antenna coil
(1) 2N366 transistor
(1) 2N464 transistor
(1) 100k resistor
(1) 5.6k resistor
(1) 10k resistor
(1) 2meg potentiometer with SPST switch
 Some good wire, solder, soldering iron, board to put it on, box (optional)

Schematic for The Lunch Box
===========================

This may get a tad confusing but just print it out and pay attention.

         [!]
          !
        51 pf
          !
       ---+----  ------------base   collector
      !        )(               2N366       +----+------/\/\/----GND
    365 pf     ()              emitter           !
       !        )(                 !              !
      +--------  ---+----         !              !
      !             !    !        !              !
     GND            /  .022mfd    !              !
                 10k\    !        !              !
                    /   GND       +------------------------emitter
                    !             !              !             2N464
                    /           .0047            !          base   collector
              2meg  \----+        !              !   +--------+       !
                    /    !       GND             !   !                !
                        GND                      !   !                !
        +-------------+.0047+--------------------+   !                !
                                                      !   +--25mfd-----+
            -----------------------------------------+   !            !
       microphone                                        +--/\/\/-----+
            ---------------------------------------------+   100k     !
                                                                      !
                  GND---->/<---------------------!+!+!+---------------+
                        switch                  Battery
                    from 2meg pot.


Notes about the schematic
=========================

1.  GND means ground
2.  The GND near the switch and the GND by the 2meg potentiometer should be
    connected.
3.  Where you see:  )(
                    ()
                    )( it is the transistor antenna coil with 15 turns of
                       regular hook-up wire around it.
4.  The middle of the loop on the left side (the left of "()") you should run
    a wire down to the "+" which has nothing attached to it. There is a .0047
    capacitor on the correct piece of wire.
5.  For the microphone use a magnetic earphone (1k to 2k).
6.  Where you see "[!]" is the antenna. Use about 8 feet of wire to broadcast
    approx 300ft. Part 15 of the FCC rules and regulation says you can't
    broadcast over 300 feet without a license. (Hahaha). Use more wire for an
    antenna for longer distances. (Attach it to the black wire on the fone
    line for about a 250 foot antenna!)

Operation of the Lunch Box
==========================

This transmitter will send the signals over the AM radio band. You use the
variable capacitor to adjust what freq. you want to use. Find a good unused
freq. down at the lower end of the scale and you're set. Use the 2 meg pot. to
adjust gain. Just fuck with it until you get what sounds good. The switch on
the 2meg is for turning the Lunch Box on and off. When everything is adjusted,
turn on an AM radio adjust it to where you think the signal is. Have a friend
lay some shit thru the Box and tune in to it. That's all there is to it. The
plans for a simple receiver are shown below:

The Lunch Box receiver
======================

(1) 9 volt battery with battery clip
(1) 365 pf variable capacitor
(1) 51 pf capacitor
(1) 1N38B diode
(1) Transistor antenna coil
(1) 2N366 transistor
(1) SPST toggle switch
(1) 1k to 2k magnetic earphone

Schematic for receiver
======================

         [!]
           !
        51 pf
          !
     +----+----+
     !         !
     )       365 pf
     (----+    !
     )    !    !
     +---------+---GND
          !
          +---*>!----base  collector-----
             diode      2N366           earphone
                        emitter    +-----
                          !        !
                         GND       !
                                    -
                                   +
                                   - battery
                                   +
           GND------>/<------------+
                  switch

Closing statement
=================

This two devices can be built for under a total of $10.00. Not too bad. Using
these devices in illegal ways is your option. If you get caught, I accept NO
responsibility for your actions. This can be a lot of fun if used correctly.
Hook it up to the red wire on the phone line and it will send the
conversation over the air waves.

Enjoy!

Read More